A motorcycle rainsuit is like insurance: You may not need it often, but when you do, you’re darn glad you’ve got it. In early April, a buddy and I rode from California to Texas to see the solar eclipse. Nelson-Rigg sent us some gear to evaluate during our nine-day, 4,200-mile journey, including Route 1 cruiser luggage (look for my review soon) and Solo Storm rainsuits, which are sold separately as a jacket and pants.
Raingear is typically used to keep riders dry in rainy conditions, but we first used our Solo Storm rainsuits on a dry morning. When we awoke before dawn on Sunday in Lordsburg, New Mexico, it was 30 degrees outside. With a 700-mile ride ahead of us, we’d be slabbing it on I-10 for an hour before the sun came up. There was no rain in the forecast, but we donned our rainsuits to block out the biting wind, and they helped keep us warm, or at least less cold.
The Solo Storm jacket and pants have a polyester oxford outer shell with a waterproof/windproof polyurethane backing and electronically taped seams. The front of the jacket has a full-length zipper with a two-layer storm flap that seals with hook-and-loop, and the wrist cuffs and tall collar also seal with adjustable hook-and-loop.
The outside of the jacket has adjustable waist straps, a drawstring around the hem, two waterproof cargo pockets, an adjustable zippered back vent, and reflective accent material. There’s breathable mesh at the back, a rain hood stored in the collar, and a built-in zippered pouch that the jacket can be stuffed into.
The Solo Storm pants have an elastic waistband with adjustment straps on both sides, and the pant legs are extra large for pulling on over boots and other gear (putting a plastic bag over your boot first makes raingear slide on more easily). The insides of the legs have a layer of heat-resistant material, the seat is reinforced with non-slip material, and there are adjustable gussets at the lower leg to keep the pants from flapping in the wind.
The true test of any motorcycle rainsuit is riding in a downpour. Just 150 miles from home at the end of the trip, that’s exactly what we encountered. After putting on the suits at a gas stop, we rode through a major gully washer on I-40, which caused traffic to slow down from its usual 80 mph to around 45. For the next 50 miles, we rode cautiously and stayed dry. We were in and out of rain for the final 100 miles, but not once did either of us feel a cold stab of water leaking through.
The Nelson-Rigg Solo Storm jacket retails for $79.95 and is available in sizes S-4XL in Black, Hi-Vis Yellow, or Orange. The pants retail for $49.95 and are available in sizes S-4XL in Black only.
Spring means the days are getting longer and the weather is warming up. Motorcycles that have been on trickle chargers in the garage are coming out into the sunshine and getting ready to hit the road. We know you are too!
Over the past 50 years, Rider has brought “Motorcycling At Its Best” to hundreds of thousands of riders like you. Your subscription dollars and support we get from advertisers has kept the lights on and the presses running for five decades.
The companies that manufacture and sell the vehicles, products, and services in this buyers guide and in the ads you see in every issue believe in our mission. We appreciate every company that supports us, and you can help pay that forward by supporting them.
SW-Motech Micro WP Tank Bag
SW-Motech’s most popular product is now available in a waterproof version. This tankbag is made from thermo-welded TPU material backed with shape-preserving EVA elements, and it attaches to the tank with SW-Motech’s PRO Tank Ring System and magnetic guide. The bag’s MOLLE-compatible lid features a magnetic closure. The bag holds 5 liters, the zippers are lockable, and reflective details provide nighttime visibility. It is available for $204. The bike-specific Tank Ring starts at $30, and riders can find the correct ring for their motorcycle by using the bike filter on the SW-Motech website.
The Roadsmart IV tires feature a revamped formula with a claimed 23% more mileage for the front tire and 26% more for the rear compared to the previous generation. The new compound has Hi Silica X and Fine Carbon technology for better grip and stopping performance in wet conditions, and a new sidewall construction improves handling. The rear tire features Multi Tread Technology, which allows the center compound to last longer while compounds on the shoulders provide better grip. Dunlop says the tires have 15% lighter steering on turn-in than their predecessor. They have a ZR speed rating and start at $227.95.
The RPHA 12 is built with HJC’s Premium Integrated Matrix EVO construction, which provides a light weight with a robust structure. The helmet prioritizes aerodynamic performance with an optimized rear spoiler and a shell shape that reduces lift and drag for stability at high speeds. Also reducing drag and noise is the HJ-42 curved faceshield (Pinlock-ready) and two-way pivot ratchet system. The interior is fully removable and washable, and the cheek pads can be changed for a custom fit. A pull tab allows quick removal of the helmet in an emergency. It comes in solid and graphic colors starting at $479.99.
National Cycle Yamaha Ténéré 700 VStream Windscreen
National Cycle’s VStream windscreen for the Yamaha Ténéré 700 offers excellent wind protection in three sizes. The patented V shape and advanced dimensional contours push wind away from the rider’s helmet for a peaceful, quiet ride, and the passenger also receives some wind protection. The screen is made of polycarbonate for better optics, and it has 23 times the impact strength of acrylic. The screen also includes a Quantum hardcoat for scratch resistance. The Sport size (12 inches tall) is available for $134.95, the Sport/Touring size (15.5 inches) is $154.95, and the Touring size (18 inches) is $164.95.
The Hair Glove prevents knotting and tangling while keeping hair protected from dirt, dust, and other damaging elements, and it provides a sleek and stylish look with its cylindrical design. Snap buttons running the length of the Hair Glove keep hair in place, and the built-in Flex-Hook attaches to an elastic band to prevent it from sliding off even at high speeds. Simply hook it, wrap it, snap it, and go. The American Flag Angel Wings with Gems design ($33.99) pictured here is available in 4-inch and 8-inch (shown) versions, and some designs offer 12-inch sizes and smaller 1.25-inch bands.
The Contour-X full-face helmet features a new Peripherally Belted Complex Laminate Construction shell that’s thinner and lighter thanks to a new fiber material and resin. The shell flares out 5mm around the opening to make the helmet easier to slide on and off, and the bottom of the shell also features Arai’s Hyper Ridge, which improves strength and shock absorption. The helmet includes a new odor-resistant, brushed-nylon interior that’s removable and washable and features adjustable Facial Contour System cheek pads. It includes seven intakes and six exhausts for airflow. Available in sizes XS-2XL starting at $739.95.
These adventure and dual-sport tires focus on off-road performance with some on-road capability as well, with a 20% on-road and 80% off-road bias. The tires’ profile and tread pattern excel in aggressive off-road riding while being predictable on-road with consistent wear and comparatively low road noise. These tires are available in a Standard version and a Dakar version with a yellow stripe, a stiffer carcass, and a longer-wearing rubber compound. The XT+ tires are available for both tubeless and tube-type applications and in various sizes starting at $103.95.
The new Nelson-Rigg Hurricane Tail Bag comes in adventure (28 liters) or dual-sport (12 liters) sizes and is constructed from heavy-duty UV-treated PVC tarpaulin material with electronically heat-welded seams to make it 100% waterproof and dustproof. The bag is mounted using heavy-duty tension lock buckles and web straps. Two adjustable cross-straps inside hold your gear in place, and the bag includes reflective piping, a rubberized carrying handle, and a MOLLE panel on the lid. The adventure size is priced at $159.95, and the dual-sport size is $139.95.
Now that spring is here, it’s time to roll your motorcycle out of the garage and knock off the accumulated dust. You can get your bike shining like new again with Spectro Performance Oils’ Motorcycle Wash and Suspension Cleaner. The Motorcycle Wash is a spray-on/rinse-off cleaner that tackles the toughest dirt, grease, grime, bug splatter, brake dust, and road film. The Suspension Cleaner is a fast-acting, deep-cleaning degreaser that removes stubborn suspension fluid, grease, dirt, and debris without harming your seals or O-rings. Available at your local dealer or powersports retailer.
This helmet is constructed with a durable and lightweight polymer shell, and inside is a dual-density EPS liner with one softer layer and one that’s firmer for progressive impact absorption. The clear faceshield comes with an antifog coating and a durable hardcoat for scratch resistance, and the shield lock ensures the shield will remain closed in all conditions. The faceshield can be raised and fully hidden under the visor, and it’s designed to accommodate goggles with straps. The helmet also includes a drop-down sunshield. Available in sizes XS-2XL and four colors for $219.95.
The IRM Moto Sahara highway pegs are simple to install and provide comfort for long-haul riding.
The IRM Moto Sahara highway pegs add a new dimension of sleek aesthetics and functionality to the usually dreary task of finding an alternate place to rest your feet on long rides. These pegs are designed to mount to the valve covers on BMW’s 2005-2009 Hexhead R-Series models, such as the R 1200 RT, R 1200 R, and R 1200 GS.
When not in use, these pegs can fold down to give the motor a stock appearance. The rider can deploy the pegs by swinging them outward with his/her boots, exposing a convenient 3-inch perch on which to rest weary feet.
When not in use, the IRM Moto Sahara highway pegs fold down and out of the way.
These pegs boast impressive mechanical engineering, which leads to a very simple installation process. The peg assembly consists of two pieces. A small, cube-shaped placeholder slides into the rear-facing valve cover recess, comes to rest on a ridge therein, and is shaped to allow the spark plug wire plenty of room. The main peg body then fills the hollow space in the valve cover over the ignition coil (where a black plastic protective cover normally lives) and mates with the aforementioned cube-shaped placeholder via four 7/64-inch stainless-steel hex bolts. After applying some blue Loctite to the bolts, they slide through the placeholder and into the main peg body. The bolts are then torqued down evenly in a star pattern with the included hex key, pulling both components together securely. Each peg takes about 10 minutes to install. The peg body components are all CNC machined and black anodized 6061 aluminum alloy. Quality of construction and materials is superb.
I tested the pegs on a scenic 2,500-mile spring tour of Texas, New Mexico, and Arizona aboard my 2008 BMW R 1200 RT test mule and came away impressed. The placement of the pegs is in the ideal position, allowing a neutral sitting position for extended periods of time – just perfect for lengthy highway stints. Actuation is easy since the leading edge of the peg facing the rider is flared outward and easy to catch with boots.
Other peg options for Hexhead RTs are generally much more expensive and cumbersome, involving buying tubular metal crash bars and then mounting conventional highway pegs to those. (Most quality crash bars for Hexhead RTs, for example, are at least two times the cost of these pegs – and that’s just for the bars without highway pegs included!) No other highway peg solution I know of is as neatly integrated into the OEM styling ethos of the BMW Hexhead R-Series as these American-made Saharas are. For $250 MSRP, the long-haul Hexhead rider can’t go wrong with these!
Spidi Tour Evo 2 Motorcycle Suit jacket in Military Green. Other color options are Black and Black/Slate.
The Spidi Tour Evo 2 Motorcycle Suit promises three-season, foul-weather functionality for the discerning on-road tourer or commuter. After riding in it for a few months, including a 3,000-plus mile winter tour of the Southwest U.S., I can report that it delivers!
The jacket’s waterproof/windproof/breathable exterior shell is comprised of rugged Cordura fabric interspersed with 3D and Tactel fabrics. For storage, there are two waterproof chest pockets, two waterproof hand pockets, and two additional front pouches, as well as one enormous pouch on the lower back. The collar is soft neoprene and hosts a snap button whose position can be adjusted via hook-and-loop. All zippers are rubberized for weather protection, and fabric lanyards are included on exterior zippers for easier gloved operation. The matching pants feature the same materials and construction, include two pockets on the thighs, and zip to the jacket.
The Spidi Tour Evo 2 pants are available in black.
The suit’s interior consists of a fixed polyester mesh lining and hook points for armor or Spidi’s optional “Step-In Wear” line of base and mid layers. Both jacket and pants include removable insulated liners, and the jacket liner can be worn by itself.
On the jacket, Spidi’s CE Level 2 “Warrior Lite” armor is standard at the shoulders and elbows, while back and chest armor is optional. I outfitted the basic package with the optional Warrior CE Level 2 back protector and the optional “Thorax Warrior” thoracic protector. The pants are equipped with EN1621-1 Level 2 armor at the hips and knees.
The Spidi Thorax Warrior is an optional piece of protection that can be worn with this suit.
The cut and styling of the suit lives up to its European pedigree, namely understated yet sophisticated, with subdued branding throughout. Reflective material is present on the front, sleeves, and rear of the jacket, as well as the side of the pant legs.
Venting, too, is plentiful. The jacket features large vents along the front and rear biceps and laterally around the torso, and when open, a bright green fabric emerges as a visual cue to zip up if storm clouds are ahead. The pants have vents running about 10.5 inches down each thigh. Adjustment points are numerous. The pants even include a set of removable suspenders.
I’ve used this suit during commuting, pleasure riding, and a 3,000-plus mile tour of the American Southwest, where we encountered temps ranging from 28 to 84 degrees. With its insulating layers and a plethora of Spidi’s optional base layers to choose from, the Tour Evo 2 is the perfect suit for winter applications. However, above 82 degrees, even with the vents wide open and the insulation liners removed, most riders will be reaching for dedicated summer mesh gear.
With this hot-weather limitation in mind, the Tour Evo 2 is one of the most versatile motorcycling suits on the market today. It survived many a full day’s riding in torrential winter downpours without letting in a drop of water or the slightest draft of wind. The Cordura material and all snaps, adjustment straps, and zippers are wearing like iron, and I have no doubt that at least 5-10 years of hard use can be expected in daily commuting duty.
Cons are few: The jacket’s main zipper terminates a full 2.5 inches above the bottom of the jacket, and while some distance is warranted (so the jacket can “split” as the rider sits), this seemed excessive and made zipping up difficult. The pants feature a right-thigh storage pouch that’s sealed with hook-and-loop, but the abrasive hook half faces the rider’s thigh so that the back side of the rider’s hand gets scraped when reaching into the pouch.
Overall, the Spidi Tour Evo 2 Motorcycle Suit is one of the finer European-style riding suits available today, and it should definitely be on the serious foul-weather rider’s short list. Available in sizes M-4XL, the jacket is priced at $749.90, and the pants are priced at $599.90.
Arai XD-5 helmet in the Discovery Blue graphic. (Action photos by Align Media)
My how time flies! It’s been 30 years since Arai launched its DS (dual-sport) helmet, which had a chinbar like a dirtbike helmet, a clear faceshield, and the round shell Arai is known for. When the first Arai XD arrived in 2004, it had the sun-blocking peak visor that has since been a signature feature of the dual-sport/adventure helmet.
New features on the Arai XD-5 include a more aerodynamic peak and a rear spoiler.
Arai’s XD-4 made its debut in 2012, and it has been a popular choice among ADV riders ever since. With a steadfast adherence to its “glancing off” philosophy, whereby the spherical shape of its helmets helps redirect impact energy, as well as its “priority for protection” prime directive, Arai does not release new helmets often nor does it chase fads. It’s been a long wait, but the new XD-5 is finally here.
The Arai XD-5 has a PB-cLc2 fiberglass shell with a super-fiber belt along the forehead.
The XD-5 begins with a Peripherally Belted Complex Laminate Construction (PB-cLc2) fiberglass shell, which has a super-fiber belt along the forehead to reinforce the area above the eyeport. The XD-5’s shell flares out an extra 5mm around the opening to make the helmet easier to slide on and off.
The Arai XD-5 has a new toolless shield/peak attachment and removal system.
The XD-5 has the latest version of Arai’s variable-axis faceshield system and the Pinlock-ready VAS-A, which maximizes surface area to improve its ability to glance off objects. Above the forehead is a new logo vent that was adapted from the Contour-X and enhances ventilation in a critical area. Also, the XD-5’s chin vent is twice as large as the XD-4’s, bringing much more air to the rider’s face. All vents on the XD-5 are adjustable, but the faceshield no longer has integrated vents.
The Arai XD-5 in the off-road configuration (peak on, faceshield off for use with goggles).
On the XD-4, removing the peak visor and faceshield required the removal of four plastic screws, two on each side. The XD-5 simplifies the process with a new toolless visor/shield attachment system, which makes it easy to switch between three configurations: adventure (visor on, shield on); off-road (visor on, shield off for use with goggles); and road (visor off, shield on). The peak visor, which is rounder in front and has less overall surface area, can also be adjusted up or down on the fly.
The Arai XD-5 in the adventure configuration (peak on, faceshield on).
Inside the helmet is a one-piece, multi-density EPS liner and a removable, washable comfort liner with adjustable pads at the cheeks, temples, and rear of the head. The cheek pads, which have an emergency-release design, have a new hook-and-loop fastener piece to facilitate easier installation of headset speakers in the ear pocket. There’s also a wire pocket in the neck roll.
The Arai XD-5 in the road configuration (peak off, faceshield on).
For everyday use, the factors that matter most are comfort, weight, and ease of use. My initial test of the XD-5 was two full days of street and off-road riding. As with other Arai helmets I’ve worn, comfort was good right away with no hot spots. The XD-5 has an intermediate oval interior head shape, which suits my noggin just fine, and the helmet is secured with a tried-and-true double D-ring chin strap.
The Arai XD-5 is more aerodynamic than the XD-4.
At 3 lb, 13 ounces for the size Medium I tested, the XD-5 isn’t the lightest ADV helmet on the market, but its average weight didn’t cause any fatigue. What was immediately noticeable was how much more aerodynamic the XD-5 feels thanks to its smaller, reshaped visor peak and new rear spoiler. There is much less buffeting, and the helmet slices through the air more cleanly when looking left or right at speed.
Thad Wolff gives the Arai XD-5 a thumbs up.
Overall, an already impressive premium ADV helmet has been made even better. The Arai XD-5 is available in XS-XXL in solid colors for $839.95-$859.95 and graphics for $949.95.
The Aerostich Messenger Bag is spacious and secure for carrying your stuff while riding. (Photos by Kevin Wing)
In the immortal words of George Carlin, “That’s the meaning of life: trying to find a place to keep your stuff.” I consider myself a tidy person, but really I’ve just developed Tetris-like efficiency when it comes to cramming stuff in my closet, my desk drawers, and – to my wife’s eternal chagrin – our garage. Surrounding her adorable blue Mini Cooper is a rabbit’s warren of shelves filled with bins (each one labeled, of course), boxes, motorcycle gear, and enough helmets for a small army.
When I travel by motorcycle, I bring stuff in saddlebags or a top trunk if possible, or perhaps in a tankbag or tailbag. But if I need to pick up a few things at the store or bring my laptop or camera equipment with me, the best option is a backpack or shoulder bag. Of the latter, one of the most practical and versatile is a Messenger Bag made by the folks at Aerostich in Duluth, Minnesota.
Messenger Bags come in four sizes: Letter (9 inches tall, 3.75 inches wide, 9 inches long at the bottom/12 inches long at the top; $107), Dispatch (12×7×12/18 inches; $137), Courier (12×7×18/23 inches; $147), and Parcel (14×9×18/26 inches; $157). Wanting maximum carrying capacity, I opted for the Parcel size, which is large enough to hold a full-face helmet and four bottles of wine, for example.
The bag’s outer flap is designed to accommodate bulky items like wide helmets and tall wine bottles. It is secured by a panel of hook-and-loop that runs the length of the flap – a 2-inch-wide panel of hook on the underside of the flap attaches to a 4-inch-wide panel of loop on the bag. There are also two adjustable closure straps with quick-release buckles.
Messenger Bags are made of 1000-denier polyurethane-backed Cordura, and they have a triangular cross-section with a seamless flat bottom. Inside is a yellow reinforced PVC waterproof lining, an organizer pocket (the Parcel has two), and a clip-on key loop.
The shoulder strap is made of 2-inch mil-spec nylon webbing, and a cam lock makes it easy to adjust the strap’s length. A removable 3.5×11.5-inch shoulder pad covered in Ultrasuede provides comfort when carrying heavy loads. The bag also has a carry handle at the top and a 2-inch panel of reflective 3M Scotchlite that runs the length of the outer flap.
Depending on how full the bag is and the rigidity of the contents, it usually stays in place while riding. Adjusting the shoulder strap so the bag hugs the body closely helps keep it secure, and Aerostich sells a stabilizer strap for $10.
All in all, the Messenger Bag is a great place to keep my stuff when I’m on the go. Multiple color options are available.
Over the past couple years, German helmet maker Schuberth has completely redesigned its lineup of motorcycle helmets. In the past, we’ve reviewed Schuberth’s modular helmets: the C5 and ADV-style E2. The S3 is a full-face helmet based on the same architecture, its shell manufactured using directly processed fiberglass combined with a special resin that’s compressed in a vacuum at high pressure. Like the C5 and E2, the S3’s shell also has a basalt layer for added strength and impact absorption.
Photo by Kevin Wing
Designed to meet Europe’s latest ECE 22.06 helmet safety standard, the S3 reaches high benchmarks for protection and has a large eyeport for better visibility (the S3 is also DOT approved). Inside the shell is a dual-density EPS liner, an intermediate-oval head shape, and a new comfort liner with customizable pads. Optional “sport” and “comfort” cheek pads and replaceable rear pads can make the interior more round or more oval. The S3 also has the Schuberth Rescue System, which allows first responders to extract the cheek pads to facilitate removal of the helmet.
Other features include an optically correct faceshield with a Pinlock anti-fog insert, a repositioned chinstrap to reduce pressure near the throat, an anti-roll-off system, a double chin air intake with an exchangeable filter, a new rear spoiler with an air extractor, and a new V-lock sunshield mechanism.
The S3 is also prewired for the optional SC2 Bluetooth 5.0 communicator (sold separately), which is made by Sena and based on the 50S with voice activation and mesh networking. HD speakers and an antenna are built into the helmet. A remote-control unit clicks into the left side of the helmet, and the SC2 main unit with a rechargeable battery plugs into the back of the helmet.
Fit and comfort are excellent, and weight is reasonable: The size Medium we tested is 3 lb, 14 ounces. While testing naked bikes for a comparison test, the S3’s slippery shape moved through the air with no buffeting, and during head checks to the side there was no unpleasant noise or wind pressure. Thanks to the aerodynamic shell and well-padded neck roll, the inside of the helmet remains reasonably quiet. The only issue I had with the S3, as well as the C5 and E2, is that it’s easy to inadvertently knock the vent on the chinbar closed when putting on the helmet or opening/closing the faceshield.
The Schuberth S3 comes in Concrete Gray (shown), Matte Black, or Glossy White for $599, as well as the Storm graphic in three colorways (blue, silver, or orange) for $699. Available sizes are XS-3XL.
I can say without hesitation that every car tire purchase I’ve made has been done somewhat grudgingly, with safety and practicality being the primary concerns. When it comes to new motorcycle tires, the return feels more worthy of the investment. The Michelin Commander III tires proved this in spades.
In a word: Giddyap!
When I was asked to review the Commander III tires on my Harley‑Davidson Heritage Softail Classic, I was a little nervous, but not because I questioned the quality. Michelin has been my brand of choice for car tires for years, but that is primarily because of their reliability in the snow and ice where I live. But I don’t ride my bike on snow and ice. I assumed many of the same attractive attributes of traction and grip would apply on a motorcycle, but was I attuned enough to my bike to recognize the difference between these new tires and my old ones?
The answer was immediately “Yes.”
There are two versions of the Michelin Commander III: Cruiser or Touring. Given the weight of my bike, I went with the Touring, which has less siping than the Cruiser tires for better stability. The potential tradeoff is less grip in the rain, but Michelin says the 100% silica‑reinforced rubber in the tires’ compound addresses this. I haven’t yet taken my bike out in a deluge to test this claim, but on a curvy road leading up to a nearby ski resort, I hit a decent storm and didn’t sense any slippage at speed.
Another feature of the Commander III is the aramid tread plies on the rear tire, which are also supposed to contribute to stability. The tires also have a more rounded profile than the previous Commander II model for better handling when the bike is leaned over. This is where that “giddyap” comes from.
After having them mounted, when I hit the numerous sweepers on the 45‑mile trip back to my house, I had a hard time keeping to the conventional wisdom of riding conservatively on new tires. It was almost like the Commander IIIs were pushing me – dare I say, showing off a little. But I refused the temptation. I promise…ahem.
Beyond performance, something else I was looking for in my new tires was longevity. Weighing in at two‑plus bills, I’m not exactly slim, but I’m also not one of those hefty Guiness World Record twins many of us remember seeing sitting on motorcycles in pictures. Nor am I a super aggressive rider, and I diligently check my tire pressure, so I was disappointed when I got less than 4,000 miles out of my previous rear tire.
Michelin claims 25% longer tread life relative to its competitors. I can’t confirm this yet, as I have only logged about 1,200 miles to date. But so far, they still look new, and with many riders reporting nearly 20,000 miles from their Commander IIIs, I have my fingers crossed for similar results.
The Michelin Commander III tires are available at online retailers or your local dealer in 11 different sizes starting at $180.99 for the front and $210.99 for the rear.
When I first got my 2004 Harley‑Davidson Heritage Softail Classic, I felt like I was cheating a little when opening and closing my saddlebags. I didn’t bother using the traditional leather straps with metal buckles, instead relying on the hidden quick‑detach plastic clips that were so much easier to secure. Unfortunately, the clips started breaking, which isn’t bad considering they’re 20 years old, but without the clips, the buckles wouldn’t work on their own.
My first stop for a replacement set was H‑D’s website, but there is only one choice of saddlebags for my bike, offering a little over 22 liters of total storage (compared to the approximate 34 liters of my stock bags).
SW‑Motech, on the other hand, offers a wide range of motorcycle luggage for pretty much any motorcycle. The company’s website makes it easy to search by make and model, but they also have several options that aren’t model specific. Capacity is important, but I was also ready to try something functionally different, so I decided on the SW‑Motech Legend Gear LC2 side bags, which have a total capacity of 27 liters.
I really like the LC2’s vintage design: a combination of Napalon synthetic leather and waxed canvas, the latter of which contributes to water protection – along with the hook‑and‑loop roll‑top closure and included waterproof inner bag. They’re smaller than my stock bags, but as I often ride for my work, I was pleased to discover I could still fit my laptop stored upright with room to spare. And if I want to carry a little extra, there are numerous loops on the exterior for attaching Legend Gear LA1 (0.8L, $24) or LA2 (1.2L, $48) accessory bags.
However, what really attracted me to the SW-Motech Legend Gear LC2 side bags was the quick‑release feature. I don’t always need luggage, and I like the clean look of my bike without the windshield and bags when I’m just cruising around town.
The quick‑release attachment of the LC2 is made of fiberglass‑reinforced polyamide and enables removal in just a couple of seconds, and when the bags are off, the black tubular steel side‑carrier bracket is barely visible. I also appreciate that when I use the bags for a trip, I can easily detach them at my destination and carry them with me, either by grabbing the top strap or using the accessory LA4 shoulder strap ($36).
Installation of the SLC side‑carrier mounting system was straightforward and took less than 15 minutes. It’s sold separately for $128 (model‑specific pricing may vary). The SW‑Motech Legend Gear LC2 side bags come in either Black or Black/Brown for $207 per side.
Cold temperatures and unexpected weather changes are the reality in the northern latitudes where many of us ride. Even though I’ve lived in Minnesota for decades, I’ve never used heated apparel before. As I prepared for a multi‑day tour of Michigan’s Upper Peninsula last October, I decided to remedy that situation by ordering an Aerostich Kanetsu Wind Blocker heated motorcycle vest to add some comfort to my late‑season ride. This electric vest gave me the feeling of the warm sun beating down on my back, especially on cold 35‑degree mornings on and off the road.
The Aerostich Kanetsu heated vest, which is made at the company’s factory in Duluth, Minnesota, and uses top‑quality stitching and zippers, proved to be hassle‑free. When ordering the vest, you specify size and the type of connection you need to hook it up to your motorcycle: BMW, SAE, or QuiConnect 2 (coaxial, which has a male‑and‑female connection). The vest’s power draw is 45 watts / 3.3 amps.
A size Large suits my 6‑foot‑2, 175‑lb frame perfectly (a detailed size chart is available on the Aerostich website), and the vest fits well underneath a jacket. It has a longer tail in the back to provide lower‑back coverage when seated in a crouched position. The vest has two pockets: one for storing the power cord and a larger one that the entire vest folds into for convenient stowage or a handy pillow for a roadside nap. Also available are optional zip-off sleeves ($97), which I added to the vest for additional insulation and to transform the vest into a jacket that can be worn off the bike.
With the vest on and powered up, I found the heat to be distributed evenly around my core as well as my neck thanks to the high collar. The power is switched on/off with a large, glove‑friendly lighted pushbutton that can be clipped onto the outside of your riding jacket. The vest provided plenty of warmth, and as the ambient temperature approached 50 degrees, I simply turned off the vest’s heat. Given the ongoing comfort, I found myself experiencing momentary guilt as my riding buddies went through the hassle of layering up and down throughout the changing riding conditions. They got tired of hearing me brag about how warm I was.
The Aerostich Kanetsu heated motorcycle vest with optional zip-off sleeves.
There are three versions of the Aerostich Kanetsu heated motorcycle vest: Airvantage ($247), which has an air‑adjustable fit and an outer shell made of Windstopper fabric; Windstopper ($197), also with a Windstopper outer shell; and Wind Blocker ($187), the version I tested, which has an outer shell made of windblocking TLTec fleece. Sizes range from S‑2XL. With this heated vest as a permanent addition to my saddlebag, I now look forward to rides on cold, blustery days.
Bringing you the Best Motorcycle News from Around the Web!
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it.Ok
